標題: High-end DAC Tube (1541A) [打印本頁] 作者: sjsiubong 時間: 2008-7-17 15:27 標題: High-end DAC Tube (1541A) Just ordered this kit from William. I will receive it next week hopefully.
By looking at the picture that William sent. This kit doesn't come with Hi End components.
Any Suggestions to modify?
http://www.hififever.com/forum/files/t_sany0121__large__195_181.jpg作者: modi 時間: 2008-7-17 21:29
整理好些線吧!作者: sjsiubong 時間: 2008-7-18 15:12
The DAC in the picture is not mine. I haven't received the kit yet.
I am sure my kit's internal cable will not be a mess,作者: samuelsum 時間: 2008-7-20 11:24
你大可以要求upgrade, 小弟都有upgrade
小弟o的線最後只可用軟身少少的mogami 2791+日本h字頭的ofc天線作同軸作者: sjsiubong 時間: 2008-7-20 15:27
Too bad William 己经寄出我的kit.
你的Upgrade 用了幾多錢?
可以分享一些pictures 嗎?
用什麼高速整流子好? 我有些 MR854 ad MUR1100.
Thanks
Bong作者: andypoon 時間: 2008-7-24 10:19
Hi BongCalifornia,
呢個世界就係咁樣,我報左今次DAC&CD機,但到下次是我們感到失落呢... 作者: kk_ho 時間: 2008-8-3 17:37
Sam Sam,
1. We should improve... V1.0, 2.0, 3.0, ......
2. We will review each course and the feedback from customer.
3. We will have some upgrade service for early customer who have V1.0, 2.0... just like what I said that to you.
4. A lot of new course / model should be adding to DIY course.
(I think you also not happy to see every time is GG...etc)
5. Continous improvement must need.
Chicken Sir作者: sjsiubong 時間: 2008-8-5 15:03
I am building this DAC.
I have a question about the Oscillator.
Should I use 1K or 475 for R25?
For C33, use 0.047UF?
Should I assemble C35?作者: sjsiubong 時間: 2008-8-10 07:53
Where in the Digital board should I connect to the tube buffer?
I have this kit sitting around for almost 1 month.
Very hard to get support!!!!
Please help.
I need to finish this kit.
Thanks,
Bong作者: admin 時間: 2008-8-11 14:04
Bong, As you use 8414
You should use 470ohm and 0.068uF, C35 no use
For tube buffer, simply connect the DAC IV output (the first NE5534 output to tube in)作者: kk_ho 時間: 2008-8-12 18:15
Bong,
I/V conversion connect to Tube buffer in.
Face to the PCB, please find R19 resistor (2K)
The left hand side of the leg is the I/V output of Left channel,
connect it to tube buffer left channel input
Find R21 resistor (2K)
Left hand side of the leg is the right output.
The GND signal (typical is a shielding wire)
Connect L GND wire near C45 GND position
Connect R GND wire near C55 GND position.
Hope can help you, any question, please email to me.
KK
kk_ho@hififever.com作者: accphoto 時間: 2008-8-13 10:58
KK Sir,
我個 CD ROM 和 DAC 的 Parts 到未.....????
未開聲係唔係可以 upgrade 呀? ^_^作者: kk_ho 時間: 2008-8-13 20:26
CDM IC ---> Arrived作者: andypoon 時間: 2008-8-19 20:17
[quote:602561ac84="Sam_Sam"][quote:602561ac84="AP"][quote:602561ac84="alfcat"]嘩, AP 兄, 去邊處買到咁多銅片?