標題: sp-10 noise [打印本頁] 作者: ronaldc 時間: 2006-11-6 19:23 標題: sp-10 noise there is noise occur when set the volumn at 1:00 position.
can here noise 4 inch away from the speaker.
although it is acceptable, hope can reduce half to the orginal.
any high hand can give suggestion? thanks.作者: losin 時間: 2006-11-6 23:08
你搭棚架?作者: ronaldc 時間: 2006-11-7 08:26
pcb only!作者: audionote 時間: 2006-11-8 01:35
如果是廠機there is noise occur when set the volumn at 1:00 position.
一定無人會買.
DlY樂趣之一解决問題.
你部機有無pay學費上堂.作者: william 時間: 2006-11-8 09:48
ronaldc, you can come to our new place to check it on the next week!作者: ronaldc 時間: 2006-11-9 00:44
thanks william.
where is the new place?作者: kk_ho 時間: 2006-11-9 13:57
Ronald,
The place is my home....
just a joke
KK.作者: DUALXEON 時間: 2006-11-15 01:54
Can I bring my economy $ pre amp JP 200 to compare.
Here, come on this Sat!作者: mkliu 時間: 2006-11-20 03:49
Hi ronaldc, how's your sp10 now?作者: ronaldc 時間: 2006-11-20 08:10
everythingis good but noise.作者: mkliu 時間: 2006-11-20 10:21
[quote:a136c944c7="ronaldc"]everythingis good but noise.[/quote]
still not fixed?
what kind of noise? hum? ele. current? or ?
can you post photo here for the inside layout?作者: losin 時間: 2006-11-20 17:51
ronaldc:你用什麼後級?作者: ronaldc 時間: 2006-11-20 21:45
image 6bi作者: losin 時間: 2006-11-20 22:16
你試下飛起條水線!不過要小心D!作者: audionote 時間: 2006-11-21 04:16
ronaldc兄
william己經跟你說了
ronaldc, you can come to our new place to check it on the next week!
為什麼你不去那邊,他們收了你錢一定辨好的.
不會是因為
KK-ho說
Unlike only "blowing" something.
你不好意思.
新手上堂certifiy to calling "金錢換取知識". 沒事的.我們全部人都明白那個道理.他們生意人也應該明白.一定解决得了.上堂時間不明白.那樣當然問老師,你不問他還可以問誰.
要是部功放有直流 出千万不要再用.有可能後面功放及喇叭死.
飛水線 :?: :?: :?:
Audionote@China作者: audionote 時間: 2006-11-24 07:22 作者: losin 時間: 2006-11-26 16:25
ronaldc兄 :問題解決了嗎?作者: ronaldc 時間: 2006-11-27 08:01
will go to william's office try to fix it!(also try to improve)作者: ynnek 時間: 2006-12-6 10:58
Hi William Sir,
Just finish my SP10, but I got similar problem.
Can here noise (See ... See / Dee...Dee) around 4 inch away from the speaker.
Setting:
-SP10 + UcD180
-volumn position at 0
-without input source